Main Unit, Built-in temperature sensor Positive-pressure Type, 25 MPa GP-M250T

GP-M250T - Main Unit, Built-in temperature sensor Positive-pressure Type, 25 MPa

*Please note that accessories depicted in the image are for illustrative purposes only and may not be included with the product.

Specifications

Model			GP-M250T
Rated pressure			0 to +25 MPa
Possible display range			–2.50 to +27.50 MPa
Allowable pressure			50 MPa
Zero-cut pressure value			±0.5% of F.S.
Burst pressure			100 MPa
Display resolution			0.01 MPa
Fluid type			Liquid that will not corrode the fluid contact part
Type of pressure			Gauge pressure
Precision			±1.0% of F.S. or less^*1
Repeatability			±0.3% of F.S. or less^*2
Temperature characteristics			±0.6% of F.S. / 10°C
Connection diameter			G3/4 (Changes to R1/8 male, R1/4 male, R3/8 male, G1/4 female, NPT1/8 male, and NPT1/4 male with available adapters.)
Box rotation angle			Maximum 330°
Medium temperature			–20 to +100°C (no freezing/condensation)^3^4
Power supply voltage			10 to 30 VDC, Ripple (P-P): 10% max., Class 2 or LPS
Current consumption			60 mA or less (when 24 V: 30 mA or less; when 12 V: 50 mA or less. Excluding output)^*5
Possible display range (temperature)			–32 to +112°C
Display method			4 column digital LED white/Vertical inversion of display is possible
Display resolution (temperature)			0.1°C
Liquid contact temperature measurement accuracy			±3.5°C (at an ambient temperature of 25°C)^*6
Indicators			Status indicator (orange, green, red, blue), output indicator 1 (orange), output indicator 2 (orange), temperature indicator (white), communication indicator (green)
Pressure hysteresis			During hysteresis mode: variable (Hysteresis is the difference between the upper setting value and the lower setting value) During window mode: fixed (0.5% of F.S.)
Pressure responsiveness	Control output		Selectable from 3 to 5000 ms
	Analogue output		As above +2 ms (90% response)
Output	Output 1 control output		NPN/PNP open collector (Selectable) 30 V or less, Max. 100 mA Residual voltage for the Main Unit is 1 V or less, N.O./N.C. selectable
	Output 2 replacement type	Control output
		Analogue output	Pressure analogue output/temperature analogue output (selectable), 4–20 mA; maximum load resistance 260 Ω
Network compatibility			IO-Link^*7
Environmental resistance	Enclosure rating		IP67
	Ambient temperature		–20 to +80°C (no freezing or condensation)^*4
	Relative humidity		35 to 85% RH (no condensation)^*4
	Vibration resistance		IEC60068-2-6 20 G (10 to 2000 Hz In each direction of X, Y, Z for 2 hours)
	Shock resistance		IEC60068-2-27 50 G (11 ms In each direction X, Y, Z 3 times)
Material properties	Port/diaphragm		Pressure port: SUSXM7/Diaphragm pressure port: Al₂O₃/O-Ring: FKM
	Other parts		Housing metal portion: SUS304, SUS303; Housing plastic portion: PPSU; Air hole^*8: PTFE, nickel-plated brass.
Applicable cable			M12 connector 4 pin
Weight			Approx. 150 g
^1 This is the value when considering linearity + hysteresis + repeatability in a stable environment of 23°C. ^2 The repeatability, based on consistent conditions, is the difference in the detection points at the time of fluctuations in the repetition. ^3 When the temperature of the piping exceeds 80°C, do not connect the cable. ^4 Condensation may cause measurement failure or breakage. To prevent condensation, take the following measures: • Make sure that the ambient temperature is the same or lower than the fluid temperature. • Use A/C for dehumidification. • Keep the sensor 30 cm or more from the cooling pipe using connective piping. ^5 Consumption current including output is 0.3 A and under. ^6 This is the value when the measured fluid is water and a KEYENCE adapter is used. ^7 IO-Link specification v1.1/COM2 (38.4 kbps) is supported. ^8 Only GP-M001T/M010T/M025T

Data Sheet (PDF) Other Models